Microsoft's Remote Access Service (RAS) provides TCP/IP over phone lines by treating your modem as a network adapter. TCP/IP applications that run over a network can run over a serial connection. iFIX can use the TCP/IP interface provided by RAS to communicate with other iFIX nodes over asynchronous lines.
Full Answer
What is RAS (Remote Access service)?
RAS (Remote Access Service) is an optional Microsoft Windows OS Family networking service that provides remote access for remote clients. A machine running Windows on which Remote Access Service (RAS) is installed is called a RAS server.
What is the Ras server in Windows NT?
RAS is fully integrated into the Windows NT security model and supports encrypted authentication, auditing, callback, and intermediary hardware security hosts. Users can be restricted to access to the RAS server only, or to access through the RAS server to all resources on the network.
What is a Ras gateway?
The computers on the private network use private, non-routable addresses. NAT maps the private addresses to the public address. This RAS Gateway feature allows organization employees with single tenant deployments to access Internet resources from behind the gateway.
How do I deploy an Ras gateway router in Windows Server 2016?
And NAT allows tenant VMs to connect to resources on the Internet, such as credit card processing resources. In Windows Server 2016, to deploy an RAS Gateway router, you must use Windows PowerShell commands. For more information, see Remote Access Cmdlets for Windows Server 2016 and Windows 10.
What is a Ras gateway?
RAS Gateway is a software router and gateway that you can use in either single tenant mode or multitenant mode. This topic discusses a single tenant mode, high availability configuration with Failover Clustering. The GRE tunnel performance statistics that are presented in this topic are valid for RAS Gateway in both single tenant and multitenant modes.
What is GRE protocol?
GRE is a lightweight tunneling protocol that can encapsulate a wide variety of network layer protocols inside virtual point-to-point links over an Internet Protocol internetwork. The Microsoft GRE implementation encapsulates both IPv4 and IPv6.
What is the maximum throughput on a GRE tunnel?
The maximum throughput on the GRE tunnel is between 400-500 Mbps.
Is RAS gateway a VPN?
Each V M has RAS Gateway installed and configured as a GRE-based VPN server.
Can you use a RAS gateway with GRE?
Because GRE tunnels provide encapsulation but not encryption, you should not use RAS Gateway configured with GRE as an Internet edge gateway. To learn about the best uses for RAS Gateway with GRE tunnels, see GRE Tunneling in Windows Server. GRE is a lightweight tunneling protocol that can encapsulate a wide variety of network layer protocols ...
How to request remote access VA?
You may request remote access by visiting the Remote Access Self Service Portal ( only available while on VA's internal network).
What is a rescue GFE?
RESCUE GFE provides a security posture check and ensures VA data is encrypted from the end device into the VA trusted network. Prior to the device connecting and being allowed onto the VA trusted network the system is checked for multiple security baselines.
Is PIV card reader site specific?
Today, the distribution of PIV card readers is site-specific. We are discussing the possibility of alternative distribution methods. If distribution processes or procedures change, we will provide updated instructions.
Is VA responsible for non-VA websites?
This page includes links to other websites outside our control and jurisdiction. VA is not responsible for the privacy practices or the content of non-VA Web sites. We encourage you to review the privacy policy or terms and conditions of those sites to fully understand what information is collected and how it is used.
Does RESCUE GFE support Windows 10?
This software is installed on all GFE laptops prior to being provided to the user. Currently RESCUE GFE supports Windows 7, Windows 8, Windows 10 and MAC OSX.
What is Remote Access Service (RAS)?
RAS (Remote Access Service) is an optional Microsoft Windows OS Family networking service that provides remote access for remote clients. A machine running Windows on which Remote Access Service (RAS) is installed is called a RAS server.
What is a RAS server?
RAS allows remote clients to connect through a telephone line or other wide area network ( WAN) link to the RAS server; from there RAS allows those clients to access resources on the network. Remote users can access network resources as though they were logged on to a machine directly connected to the network.
What is the function called when a caller dials in to a RAS server?
The RAS server dials the user back at the phone number the user specifies. This function is called callback.
What is remote access in Windows 2000?
On Windows 2000 Server, remote access functionality is provided by Routing and Remote Access, which supports both dial-up networking and virtual private networks.
How to connect a RAS transducer to an Ultraprobe?
Just mount the RAS transducer on your test subject, attach a BNC cable, run the cable through an access hole. Now, every time you come by, just plug it into your Ultraprobe 9000, 10,000, 15,000 or 401, record your data and move on.
How to test multiple points remotely?
Connect and test single or multiple points remotely. Permanently mount a RAS to a test point and run a coax cable to the Switch Box. Once connected, you may test up to 8 test points at a time. To test, attach a RAM (Remote Access Module) to the Switchbox, select a test point indicator and collect your data. It’s that easy!
How to test RAM on Ultraprobe?
Mount the RAS on the test point and run a cable to an access area where a RAM (Remote Access Module) can be connected. When the point is to be tested, plug the RAM into your Ultraprobe and take your reading. Installation is very simple and testing is really easy.
